The Wacker Neuson Connecting Rod Complete is a genuine OEM component designed for a wide range of Wacker Neuson ride-on trowels, portable generators, floor saws, and reversible vibratory plate compactors. As a factory-sourced part, the is manufactured to the exact tolerances required by the original engine assembly, ensuring proper fit and function across every compatible machine in this lineup. Confirmed fitment includes the CRT48-34V ride-on trowel series, GP5600A, GP6600A, GPS5600A, GPS6600A, GV5600A, and GV6600A generator families, BFS floor saw models including the BFS 1335A, BFS 1345A, BFS 1350A series and variants, the CT48-13A-V walk-behind trowel, and the BPU 5045A and BPU 5545A reversible vibratory plates.
Key Features
- OEM-Spec Rod Geometry — Manufactured to the original bearing bore and pin dimensions, so bearing clearances and crank pin alignment remain within the engine builder's specification.
- Direct Drop-In Installation — Matches the original connecting rod bolt pattern and cap fitment, allowing straightforward installation during a top-end or bottom-end engine rebuild without machining or adapting.
- Broad Cross-Family Fitment — A single part number covers CRT48 ride-on trowels, CT48 walk-behind trowels, GP/GPS/GV 5600A–6600A portable generators, BFS 1318–1350 floor saws, and BPU 5045A/5545A vibratory plates sharing a common engine platform.
- Restored Power Transfer — A worn or cracked connecting rod causes bearing knock, loss of compression, and eventual engine seizure; replacing it with this genuine part restores the full piston-to-crankshaft power transfer the engine was designed to deliver.
- Engine Integrity Under Load — For cutting, compaction, and concrete finishing equipment that runs at sustained high loads, a correctly specced connecting rod is critical to maintaining stable combustion cycle timing and preventing catastrophic internal engine failure.
The connecting rod is the mechanical link between the piston and the crankshaft inside the engine. With each combustion cycle, it converts the up-and-down motion of the piston into the rotational force that drives the crankshaft and ultimately powers the machine. Over time, the rod bearings and pin bore can wear due to oil starvation, overloading, or simple high-hour fatigue, leading to knocking, vibration, and — if left unaddressed — a seized engine. Replacing the connecting rod complete with a genuine OEM part like the Wacker Neuson 5000082813 restores the correct clearances and load-bearing capacity the engine depends on for consistent, full-power operation.
Part Details
| Part Number | 5000082813 |
|---|---|
| Old Part Number | 0082813 |
| Brand | Wacker Neuson |
| Part Type | Genuine OEM |
| Description | Connecting Rod Complete |
Compatibility & Fitment
| Name | Model | Machine Number |
|---|---|---|
| 1220mm/48in Ride-on Trowel | CRT48-34V | 5000620805, 5000620075, 5200004935 |
| GPS5600A,CAN GFI | GPS5600A | 5000620096, 5000620383, 5000620328, 5000620981 |
| GPS6600A GENERATOR,CAN GFI | GPS6600A | 5000620102, 5000620386, 5000620331, 5000620047, 5000620099, 5000620016 |
| CT48-13A-V Trowel | CT48-13A-V | 5000009452, 5000620836 |
| Premium Portable Generator | GP5600A | 5000620094, 5000620095, 5000620326, 5000620327, 5000620381, 5000620382 |
| GP6600A GENERATOR,CAN GFI | GP6600A | 5000620100, 5000620101, 5000620329, 5000620330, 5000620384, 5000620045, 5000620046, 5000620097, 5000620098, 5000620014, 5000620015 |
| Premium Portable Generator | GP6600 | 5000620385 |
| GPS6600A Generator, CSA | GPS6600 | 5000620988 |
| Reversible Vibratory Plate, 50 kN, 45cm/18in | BPU 5045A | 5000008545 |
| Basic floor saw, 450mm/18in | BFS 1345AB | 5000008764, 5000610141 |
| BFS1350ALS-SAW | BFS 1350ALS | 5000008885, 5000610399 |
| Gasoline Floor Saw, Ø 450 (350 ) | BFS 100 | 5000007352 |
| Gasoline Floor Saw, 450 drive, cutmatic | BFS 1345AS | 5000008699 |
| Gasoline Floor Saw, 450 drive, cutmatic | BFS 1345ALS | 5000008700 |
| Gasoline Floor Saw, Ø 500 driv e, cutmatic | BFS 1350AS | 5000008752 |
| BFS1350AL-SAW | BFS 1350AL | 5000008898, 5000610398 |
| BFS 1318AB SAW | BFS 1318AB | 5000610091 |
| Gasoline Floor Saw, 450 cutmat ic | BFS 1345A | 5000008697 |
| Gasoline Floor Saw, 450 cutmat ic | BFS 1345AL | 5000008698 |
| Gasoline Floor Saw, Ø 500 cutm atic | BFS 1350A | 5000008751 |
| BFS 1345 SAW,ABZ | BFS 1345ABZ | 5000610242 |
| Value Generator | GV5600A | 5000620410, 5000620288, 5000620335 |
| Value Portable Generator | GV5600 | 5000620995 |
| Value Portable Generators | GV6600 | 5000620996 |
| Gasoline Floor Saw, 350 cutmat ic | BFS 1335A | 5000008696 |
| BPU5545A-VIBROPLATE | BPU 5545A | 5000610346 |
| Value Generator, 60Hz | GV6600A | 5000620289, 5000620336 |
| Vibratory Plate BPU 5545A US | BPU 5545A US | 5100000678 |
Verify Before You Order
Fitment is machine-number and revision-specific; always confirm your model and serial number against the fitment list.
Why Buy From DHS Equipment
Every part is verified against the manufacturer's part number before it ships, so what you order is what arrives. We carry parts from leading OEM brands and our own DHS Quality Parts line of professional aftermarket components. Need help finding the right part? Our team is available to confirm compatibility whenever you need it. Orders are processed fast to keep your jobs on track. We don't just sell parts. We keep you jobsite ready.
Questions? Contact our team at [email protected] or 866-611-9369 — DHS Equipment is here to help you maintain peak performance.
