The Wacker Neuson is a genuine OEM Idle Jet designed for a wide range of Wacker Neuson equipment, including PT2 and PDT2/PDT3 trash and diaphragm pumps, CT36-6 concrete trowels, GP2600 portable generators, VP and WP series single-direction vibratory plate compactors, BPU2540 reversible vibratory plates, and BFS series floor saws. As a factory-original component, the meets the precise carburetor specifications set by Wacker Neuson, ensuring correct fuel metering at idle across every compatible machine. This broad fitment makes the a practical stock item for dealers, rental fleets, and service shops running multiple Wacker Neuson product lines. Verify your model and machine number against the fitment list before ordering to confirm compatibility.
Key Features
- Factory-Calibrated Fuel Metering: — Sized to OEM carburetor specification, this idle jet delivers the correct fuel-to-air ratio at low throttle, supporting stable idle and clean transitions to full throttle.
- Genuine OEM Component: — Sourced directly from Wacker Neuson, the 5000156537 matches the original jet bore diameter and thread pitch, dropping into the carburetor body without rework or improvisation.
- Exceptionally Wide Fitment: — A single part number covers VP and WP plate compactors, BPU2540 reversible plates, PT2/PDT2/PDT3 pumps, PG2/PG3 dewatering pumps, CT36-6 trowels, GP2600 generators, and BFS floor saws — ideal for multi-machine service inventories.
- Restores Smooth Idle and Throttle Response: — A worn or clogged idle jet causes rough idling, stalling at low RPM, and poor throttle pickup. Replacing it with the correct OEM jet restores crisp, stable engine behavior across the power band.
- Fuel System Integrity: — Correct jet sizing is critical to maintaining a safe and efficient fuel circuit; an improperly sized or damaged jet can cause lean-running conditions that lead to premature engine wear or overheating.
The idle jet is a small but precisely engineered component located inside the carburetor. It controls how much fuel enters the engine's air stream when the throttle is at or near the closed position — in other words, it governs idle speed and the initial phase of throttle opening. Because the idle circuit operates independently of the main fuel circuit, even a partially blocked or incorrectly sized idle jet will cause the engine to run rough, hunt for idle, or stall when the operator backs off the throttle. Over time, ethanol-blended fuel deposits and varnish buildup are the most common causes of idle jet failure, making it a routine carburetor service item on gasoline-powered equipment.
Part Details
| Part Number | 5000156537 |
|---|---|
| Old Part Number | 0156537 |
| Brand | Wacker Neuson |
| Part Type | Genuine OEM |
| Description | Idle Jet |
Compatibility & Fitment
| Name | Model | Machine Number |
|---|---|---|
| PT2 Pump | PT2 | 5000009318, 5000009319, 5000009320 |
| CT36-6 Trowel | CT36-6 | 5000009443, 5000620830 |
| Premium Portable Generator | GP2600 | 5000620088, 5000620116 |
| 50mm/2in Diaphragm Trash Pump | PDT2 | 5000009494, 5000620770 |
| 75mm/3in Diaphragm Trash Pumps | PDT3 | 5000009495, 5000620774 |
| PG2 Dewatering Pump | PG2 | 5000009496, 5000009497 |
| PG3 Dewatering Pump | PG3 | 5000009498, 5000009499 |
| Value Vibratory Plate, 11kN, 3 50mm/13.8in | VP1135R | 5000008709, 5000009071, 5000630061 |
| Value Vibratory Plate, 11 kN, 356mm/14in | VP1135RW | 5000009251, 5000009512 |
| Value Vibratory Plate, 13 kN, 400mm/15.5in | VP1340RW | 5000009034 |
| Value Vibratory Plate, 15 kN, 500mm/19.5in | VP1550RW | 5000009030 |
| Value Vibratory Plate, 13 kN, 400mm/15.5in | VP1340R | 5000009033 |
| VP1340W VIBROPLATE | VP1340W | 5000008706, 5000630051 |
| Value Vibratory Plate, 15 kN, 500mm/19.5in | VP1550R | 5000009029, 5000630056 |
| Value Vibratory Plate, 20 kN, 500mm/19.5in | VP2050R | 5000009088, 5000630063 |
| VP1550W VIBROPLATE | VP1550W | 5000008708, 5000630013, 5000630053 |
| Vibratory Soil Plate, 60 kN | VP60X | 5000009533 |
| VP1340 Single Direction Vibratory Plate | VP1340 | 5000008705, 5000630050 |
| Vibratory Soil Plate, 50 kN | VP50X | 5000009531 |
| Single Direction Plate | VPR70 | 5000006909 |
| WP1540W VIBROPLATE | WP1540W | 5000009326, 5000630018, 5000009547, 5000630066 |
| VP1550 VIBROPLATE | VP1550 | 5000008707, 5000630052 |
| WP1550W VIBROPLATE | WP1550W | 5000009324, 5000009548, 5000630020, 5000630064 |
| WP1550 VIBROPLATE | WP1550 | 5000009325, 5000630065 |
| WP1540 VIBROPLATE | WP1540 | 5000009327, 5000630067 |
| Value Vibratory Plate | VP2050I | 5000009541 |
| VP50Xw-VIBROPLATE | VP50Xw | 5000630094 |
| VP60Xw-VIBROPLATE | VP60Xw | 5000630095 |
| BFS12 FLOOR SAW | BFS12 | 5000630000 |
| WP 2050W | WP2050W | 5000630023 |
| WPP 1540W | WPP1540W | 5000630027 |
| WPP 1550W | WPP1550W | 5000630031 |
| WPP 1550Ww | WPP1550Ww | 5000630032 |
| Single Direction Plate | AP1135R | 5000009518 |
| WPP 1540Ww | WPP1540Ww | 5000630028 |
| Single Direction Asphalt Plate | VP2050RW | 5000009511 |
| VP2050W VIBROPLATE | VP2050W | 5000009537 |
| Walk-behind Rollers | RS600 | 5000630194, 5000630136 |
| Modular Internal Vibrators | RD 3.7 | 5000006908 |
| 500mm/50in, 20kN Value Vibrato ry Plate | VP2050 | 5000009530 |
| Value Vibratory Plate, 11kN 356mm/14in | VP1135R-AU | 5000630102 |
| Single Direction Plates | VP1340W-L | 5000630001 |
| Single Direction Plates | VP1340W-LL | 5000630002 |
| Single Direction Plates | VP1340W-LF | 5000630003 |
| Floor Saws | BFS1214 | 5000630004, 5000630093 |
| Single Direction Plate | WP1550Ww | 5000630113 |
| Single Direction Plate | WP2050Ww | 5000630116 |
| VP1340W VIBROPLATE, W/WHEEL KIT | VP1340W w/WH | 5000630121 |
| Floor Saw | BFS 12 | 5000630092 |
| Single Direction Plate | WP1540Ww | 5000630111 |
| Gas Reversible Vibratory Plate ,25 kN,40cm/16in | BPU 2540 | 5000008954 |
| Floor Saw | BFSX1214 | 5000630101 |
| Floor Saws | BFS 614B | 5000009526 |
| 50mm/2in Diaphragm Trash Pump | PDI2 | 5000009489 |
| 75mm/3in Diaphragm Trash Pump | PDI3 | 5000009491, 5000009492 |
Verify Before You Order
Fitment is machine-number and revision-specific; always confirm your model and serial number against the fitment list.
Why Buy From DHS Equipment
Every part is verified against the manufacturer's part number before it ships, so what you order is what arrives. We carry parts from leading OEM brands and our own DHS Quality Parts line of professional aftermarket components. Need help finding the right part? Our team is available to confirm compatibility whenever you need it. Orders are processed fast to keep your jobs on track. We don't just sell parts. We keep you jobsite ready.
Questions? Contact our team at [email protected] or 866-611-9369 — DHS Equipment is here to help you maintain peak performance.
